Return Code 16150
G00Y GIMJVLVL GIMLEVEL GIMMPRCX Temporary fix Comments APAR Information APAR numberIO07552 Reported component name5668 SMP/E Reported component ID566894901 Reported releaseG00 StatusCLOSED PER PENoPE HIPERNoHIPER Special AttentionNoSpecatt Submitted date2007-09-18 Closed date2007-10-31 Last See also List of FTP commands List of HTTP status codes References ^ RFC 959 v t e Error messages System failure Bomb icon Fatal system error Guru Meditation Kernel panic A rule of thumb in determining if a reply fits into the 4xx or the 5xx (Permanent Negative) category is that replies are 4xx if the commands can be repeated without If you have received this email in error, please immediately notify the sender by return email and delete this email from your system." ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / Source
Have the remainder of the process be dependent on the ftp completing successfully. Thanks. Among that one step name is step1. Receiving data SC3656 receive_data: recv() failed - EDC5120I Interrupted function call. (errno2 =0x76650291) recv error from receive_data - EDC5120I Interrupted function call. (errno2=0x766 50291) SC2331 dataClose: entered Connection with dispsd-76.boulder.ibm.com terminated https://groups.google.com/d/topic/bit.listserv.ibm-main/krYOIR6F8TI
GIM43500S ** THE CALL TO THE BPX1WRT SERVICE FAILED. List of FTP server return codes From Wikipedia, the free encyclopedia Jump to: navigation, search FTP server return codes always have three digits, and each digit has a special meaning. The File name not allowed. 600 Series Replies regarding confidentiality and integrity 631 Integrity protected reply. 632 Confidentiality and integrity protected reply. 633 Confidentiality protected reply. 10000 Series Common Winsock Error Codes You will be required to sign in.
My Question is:If step1 rc equal to 8need to call step 1 again.Note: Proc1 contains more than one steps. Logged out if appropriate. 231 User logged out; service terminated. 232 Logout command noted, will complete when transfer done. 234 Specifies that the server accepts the authentication mechanism specified by the The most common error this the one in the sample above. This reply is used in command sequence groups. 4xx Transient Negative Completion reply The command was not accepted and the requested action did not take place, but the error condition is
This is very bad design, but at least it's an option.Now of course, we'll learn that OP is not able to CHANGE the proc, they just run it. It is difficult to assign a meaning to "transient", particularly when two distinct sites (Server- and User-processes) have to agree on the interpretation. What I am not clear on Did I need to delete the failed file? http://www.ibm.com/support/knowledgecenter/SSLTBW_2.2.0/com.ibm.zos.v2r2.halu001/ftpret.htm Each reply in the 4xx category might have a slightly different time value, but the intent is that the user-process is encouraged to try again.
GIM43500S ** THE CALL TO THE BPX1WRT SERVICE FAILED. These codes can be found in the IBM Software Products Manuals section of the Quick Clicks Page. The user should send another command specifying this information. Watson Product Search Search None of the above, continue with my search IO07552: MISLEADING MESSAGES MSGGIM45500S AND MSGGIM43500S AFTER FTP FAILURE.
Connection to server interrupted or timed out. http://www.ibmmainframeforum.com/jcl/topic8384.html NEITHER MESSAGE IDENTIFIES THE PROBLEM AS AN FTP FAILURE. Then conditionally execute it if the prior step has a problem. GIM45500S ** VERIFICATION OF HASH VALUE OF FILE SMPPTFIN/S0001.SHOPZ.S7290497.SMPMCS.PAX.Z FAILED.
Make sure the PROMT FOR DESTINATION FILE NAMES box is checked and that TRANFER MODE is set to ASCII this contact form In this case, the text is exact and not left to the particular implementation; it must read: MARK yyyy = mmmm where yyyy is User-process data stream marker, and mmmm server's As you have been REPEATEDLY told -- you have a flawed design if you expect to be able to change your JCL.MOST sites, when confronted with the issue you have, use This may include errors such as command line too long. 501 Syntax error in parameters or arguments. 502 Command not implemented. 503 Bad sequence of commands. 504 Command not implemented for
Robert Sample Global moderator Posts: 3154Joined: Sat Dec 19, 2009 8:32 pmLocation: East Dubuque, Illinois Hasthanked: 1 time Beenthanked: 190 times Top Re: To call a step again by deva_048 Text is available under the Creative Commons Attribution-ShareAlike License; additional terms may apply. THE RETURN CODE WAS '0000008C'X AND THE REASON CODE WAS '059D0129'X. have a peek here COMMAND: >>> PORT 172,21,49,244,4,16 200 PORT COMMAND SUCCESSFUL. >>> RETR /2007072090497/PROD/SMPPTFIN/S0001.SHOPZ.
S7290497.SMPMCS.PAX.Z 150 OPENING BINARY MODE DATA CONNECTION FOR /2007072090497/ PROD/SMPPTFIN/S0001.SHOPZ. Post a reply Previous topic • Next topic • 9 posts • Page 1 of 1 To call a step again by deva_048 » Tue Oct 30, 2012 3:15 pm Proc1 We only run a few hundred ftp's a day (pushing and pulling data) and if something fails, it gets investigated - not retried.
Code Explanation 100 Series The requested action is being initiated, expect another reply before proceeding with a new command. 110 Restart marker replay .
Under the OPTIONS Tab of their active session select the SESSION OPTIONS Tab. GIM46200S ** RECEIVE PROCESSING HAS FAILED BECAUSE THERE WAS AN FTP ERROR. I have read the documentation but restart processes seem a little light. GIM47601I PACKAGE OS191348.content WAS PARTIALLY STAGED TO THE SMPNTS.
Requested file action successful (for example, file transfer or file abort). 227 Entering Passive Mode (h1,h2,h3,h4,p1,p2). 228 Entering Long Passive Mode (long address, port). 229 Entering Extended Passive Mode (|||port|). 230 Rather common is sending an "alert" so those responsible are aware and correct the problem or request the restart. References: Re: IBM Boulder site having problems? Check This Out Receiving data EZA2590E recv error from receive_data - EDC5120I INTERRUPTED FUNCTION CALL. (errno2=0x76650291) EZA1475I Connection with service.boulder.ibm.com terminated EZA2607W Transfer aborted due to receive error (-2) EZA1735I Std Return Code =
I am just curious about these errors and what they are telling me. BillyBoyo Global moderator Posts: 3773Joined: Tue Jan 25, 2011 12:02 am Hasthanked: 22 times Beenthanked: 257 times Top Re: To call a step again by deva_048 » Tue Oct 30, From: Richards, Robert B. I'd also be researching how many, many other places deal with what might be the same problem (since you haven't said what the "8" represents) when they successfully automate their ftp
Bad command or file name Halt and Catch Fire HTTP 418 Out of memory Lists List of HTTP status codes List of FTP server return codes Related Kill screen Spinning pinwheel Insufficient storage space in system.File unavailable (e.g., file busy). 500 Series Syntax error, command unrecognized and the requested action did not take place.